Embraer E-Jet Memory Items

Embraer E-JetATPL · Type rating12 min readUpdated Nov 2026
Definition

Embraer E-Jet memory items, listed as recall items in E-Jet operating documents, are the first actions of a few time-critical non-normal procedures, done by the crew without reading them. The operator's quick access checklist or the QRH then confirms those actions and completes the procedure.

On the Embraer E-Jets, as on other airliners, most failures are handled by reading a checklist, but a few cannot wait for one. For those, the crew carries out the opening actions from memory, the memory items, which E-Jet documents call recall items; a checklist then confirms them and finishes the procedure. A second group of events, the rejected takeoff, the windshear escape, the response to a TCAS resolution advisory and the upset recoveries, are maneuvers that are flown from start to finish rather than read.

This article covers the first-generation E190, the E1, and the E190-E2. Its figures come from a summary of the E190 and E190-E2 operating manuals, one airline's E2 procedures and Transport Canada's operational evaluation of the E-Jets. Recall items vary with the generation, the QRH revision and the operator, so the operator's current quick access checklist and QRH always govern. The Boeing equivalent is in B737 memory items.

Recall items, the QAC and the QRH

E-Jet non-normal procedures sit in three layers. In one operator's documents the recall items lead into the quick access checklist (QAC), a short card of time-critical procedures: abnormal engine start, cabin altitude high, emergency descent, battery overtemperature, dual engine failure, APU and cargo fires, jammed flight controls, the smoke procedures, and engine fire, severe damage or separation. Everything else is in the QRH. The E190-E2 QRH is split four ways: emergency and abnormal procedures (EAP), one chapter per system, for EICAS alerts; non-annunciated procedures (NAP) for events without an EICAS message, divided into emergency items (ditching, dual engine failure, emergency descent, forced landing) and abnormal ones; supplementary normal procedures (NP); and ground resets (GR). Volcanic ash, unreliable airspeed and the loss of all fuel quantity indications are QRH non-annunciated procedures, not QAC items.

In that operator's procedures, on the ground the right-seat pilot (RSP) reads the QAC and the left-seat pilot (LSP) acts, and vital items are not confirmed; in flight the pilot monitoring (PM) reads and the pilot flying (PF) acts. In flight a few vital items need a cross-check by both pilots before anyone touches them: thrust levers, START/STOP selectors, fire handles (only for pulling) and the IDG disconnect. Thrust levers belong to the PF, START/STOP selectors to the PM. Before any checklist, the PF flies the airplane and runs PPAA: power, performance (thrust, gear, flaps and speedbrake), an initial analysis such as "engine failure" and an initial action.

The short recall items confirmed by the sources are:

Event Recall items Model confirmed
Smoke, fire or fumes without an EICAS message Crew oxygen masks: DON, 100 %; crew communication: ESTABLISH E190-E2
Engine abnormal start Affected engine START/STOP selector: STOP E190-E2
Jammed elevator Elevator disconnect handle: PULL E190-E2
Jammed aileron Aileron disconnect handle: PULL E190 E1 and E190-E2
Steering runaway Steer disconnect switch: PRESS; steer with differential braking and rudder E190-E2
Pitch trim runaway A/P disconnect button: PRESS AND HOLD; pitch trim system 1 and 2 cutout buttons: PUSH IN E190 E1 only
Roll or yaw trim runaway A/P disconnect button: PRESS AND HOLD E190 E1 only

With the smoke items the headset goes back onto the neck. After an abnormal start in which fuel flow was seen, the engine is motored. Once the steering is disconnected the nosewheel casters freely, hence the brakes and rudder. On the E1, once the aileron disconnect has been pulled, only maintenance on the ground can reconnect the system. After an E1 pitch trim runaway, one operator adds: declare an emergency, ask for an altitude band separated from traffic, use the trim sparingly, avoid configuration changes and land with reduced flap.

Note: there is no pitch trim runaway procedure on the E190-E2. Its trim acts mainly through the elevator, the stabilizer moving only to unload it, and Transport Canada lists the pitch and the roll and yaw trim runaway procedures as removed for the E2 (see E-Jet flight controls).

Memory items cover only the first seconds of a failure; on the E-Jet the QAC or the QRH then completes the procedure. The ECAM, the sidestick and the 400 ft mark are the A320's: the E-Jet has EICAS alerting and control columns. v1prep schematic.
Memory items cover only the first seconds of a failure; on the E-Jet the QAC or the QRH then completes the procedure. The ECAM, the sidestick and the 400 ft mark are the A320's: the E-Jet has EICAS alerting and control columns. v1prep schematic.Illustration © v1prep

Engine fire, severe damage or separation

An engine emergency starts with recognizing which kind it is, because the E190-E2 sends them to different checklists:

Indications Event Checklist
Fire warning, red FIRE on the ITT indication, fire handle lit; thrust usually unaffected Engine fire QAC or QRH NAP, ENG FIRE, SEVERE DAMAGE OR SEPARATION
Loud bang, N1 and N2 falling, ITT rising briefly, loss of thrust Severe damage The same
Amber dashes in place of the engine indications, no thrust rating mode Separation The same
Amber FAIL on N1, red oil pressure, continuous ignition selected by the FADEC Flameout QRH EAP, ENG FAIL
Fuel burning in the turbine casing during a ground start or shutdown, usually with no cockpit indication Tailpipe fire QRH NAP, ENG TAILPIPE FIRE

A seized engine also goes to the fire, severe damage or separation checklist. Its line-by-line sequence is on the operator's QAC and is not reproduced here. The thrust lever, the START/STOP selector and the fire handle are all vital items, so in flight each is confirmed by both pilots before it is moved, or for the fire handle before it is pulled, the PF taking the thrust lever and the PM the selector. Pulling the fire handle shuts off fuel, hydraulic fluid and bleed air for that engine at their shutoff valves, and the engines share two cross-connected bottles, A and B (see E-Jet fire protection and oxygen).

Warning: a fire handle whose light has gone out does not prove that the fire is out. As long as EICAS still shows ENG FIRE, the fire condition has not ended.

An engine failure at or above V1 changes the takeoff. In one operator's E190-E2 procedures the PF rotates more gently than with both engines: 1.5 to 2° per second, to 10° nose-up, rather than about 3° per second toward 18°. The PF then holds V2 to V2 + 10 kt, using roughly half rudder pedal at first, and keeps the sky pointer centered with smooth inputs. With ATTCS on and the thrust levers in TO/GA, the FADEC sets reserve thrust once the engines' N1 values differ by more than 15 %. Rudder trim then differs by generation. On the E1 the yaw is trimmed before the autopilot is engaged, to about one dot in climb and cruise, half a dot on approach and neutral on final. On the E2 the best beta function puts in roughly 75 % of the required rudder and displays a cyan target for the sideslip, and yaw trim is disabled while it acts (see engine failure and engine fire).

A twin-engined jet with a shark's face painted on its nose climbing steeply after takeoff, its landing gear still down.
An Embraer E190-E2 taking off at the 2018 Farnborough air show. After an engine failure at or above V1, one operator rotates the E2 at 1.5 to 2° per second toward 10°.Steve Lynes from Sandshurst, United Kingdom · CC BY 2.0 · Wikimedia Commons

Rejected takeoff

The 80 kt call divides the takeoff roll. Besides cross-checking the airspeeds, it serves as a check that neither pilot is incapacitated and as the threshold of the high-energy regime. Above 80 kt one operator's E190-E2 procedures reject only for:

On a short runway or in low visibility the crew is go-minded.

The RTO autobrake is set before takeoff. It can be selected only on the ground and arms when there is weight on wheels, no failure and an average wheel speed under 60 kt. Braking starts once the wheels turn faster than 60 kt and both thrust levers are at idle or in reverse; pressing a brake pedal above 60 kt disarms it. The autothrottle disengages by itself when reverse is deployed in a rejected takeoff. The reverse thrust used depends on the speed at the rejection:

Rejected at Reverse thrust
Below 80 kt Idle reverse only
Above 80 kt Maximum reverse, reduced to idle reverse at 60 kt and closed to idle thrust at 30 kt

The pilots share the work by seat. In the operator's procedures the RSP's tasks are to confirm that the spoilers and reversers have deployed, call "60 kt", tell ATC and set flaps 5 in case an evacuation follows. The LSP brings the airplane to a stop, letting the RTO autobrake slow it to a safe taxi speed, then applies the parking brake and calls "Cabin crew at stations". The runway is left only by a high-speed exit, if at all, and the LSP tries to turn the airplane into wind.

Without an evacuation, the PA call is "Cabin crew and passengers keep your seats". With one, the LSP shuts down the engines and calls "QRH EMG EVAC", the RSP reads and the LSP acts, and the cabin hears "Cabin crew at stations", then "Emergency, open seat belts, evacuate" (see emergency evacuation and takeoff procedures and rejected takeoff).

View through a cabin window of a jet's wing on the runway, with a row of spoiler panels raised along its upper surface.
Spoiler panels raised on an Embraer 190's wing on the runway at Fort Lauderdale. In one operator's rejected takeoff procedure, the right-seat pilot checks the spoilers and reversers.Sunnya343 · CC BY-SA 4.0 · Wikimedia Commons

Windshear and EGPWS warnings

The E190-E2's reactive windshear alerting, EGPWS Mode 7, works from 10 ft to 1,500 ft above the ground, provided the EGPWS and the radio altimeter are working. It has two levels:

Alert Shear detected Aural and alerting
Caution Increasing headwind or updraft "Caution, windshear", master caution
Warning Decreasing headwind, tailwind or downdraft "Windshear" three times, master warning

The windshear escape answers the warning. The PF moves the thrust levers to maximum and presses TO/GA. The autopilot disconnects, reserve (RSV) thrust is activated, the autothrottle goes to TO/GA, and the flight director's WSHR mode gives escape guidance with wings level and pitch limited to the stick shaker angle. The crew cannot select WSHR: it engages automatically when windshear is detected with the thrust levers at the TO/GA detent or the flight director in TO or GA, and pressing TO/GA once windshear is detected engages it otherwise.

The configuration is left alone. Retracting flaps in the shear could stall the wing, and if the airplane does strike the ground it is better off with the gear down. The PF uses small inputs and keeps the wings level, while the PM watches the vertical speed and calls out any descent.

An airliner flight deck seen from behind the seats: four wide display screens across the panel, two control yokes, the pedestal and the overhead panel.
The flight deck of an Embraer E195-E2, laid out like the E190-E2's. After a windshear warning the thrust levers on the pedestal go to maximum and TO/GA is pressed.EneasMx · CC BY 4.0 · Wikimedia Commons

E190-E2s fitted with the RDR-4000 weather radar, an E2 option, also have predictive windshear. It looks up to 5 NM ahead, works automatically below 1,800 ft AGL and alerts at or below 1,200 ft AGL. On takeoff its warning is "Windshear ahead, windshear ahead", and the crew considers rejecting; on approach it is "Go-around, windshear ahead", and the crew goes around. The escape maneuver itself is flown only when the airplane is actually in windshear (see windshear and microbursts).

The EGPWS warning "Pull up" comes from two of the basic modes: Mode 1, excessive descent rate, which follows "Sink rate" with "Pull up", and Mode 2, excessive terrain closure, which follows "Terrain" with "Pull up". The other modes warn of a height loss after takeoff or go-around (Mode 3, "Don't sink"), unsafe terrain clearance (Mode 4, "Too low terrain", "Too low gear", "Too low flap"), deviation below the glideslope (Mode 5) and excessive bank (Mode 6). On the terrain display solid red means 30 seconds to impact and solid yellow 60 seconds; when the display appears by itself, the range goes to 10 NM and the weather radar picture is removed.

A PULL UP warning is answered at once, from memory, with a terrain escape maneuver, without first working out its cause. The E-Jet's pitch and thrust targets for that maneuver are in the operator's QRH and are not given by the sources used here; the general technique is in GPWS and TAWS.

Exam tip: "Caution, windshear" means an increasing headwind or updraft and brings a master caution; three "Windshear" calls mean a decreasing headwind, tailwind or downdraft and bring the escape maneuver. A predictive "Go-around, windshear ahead" calls for a go-around, not the escape.

Emergency descent and cabin altitude

A cabin altitude of 9,700 ft triggers the CABIN ALTITUDE HI master warning; for airports above 9,400 ft elevation the threshold is 500 ft above the airport. The 8,000 ft value among the limitations is the maximum cabin altitude, not a warning level. Cabin altitude high and emergency descent are both QAC items, and on the E190-E2 the emergency descent is also in the emergency part of the non-annunciated procedures.

The emergency descent in one operator's E190-E2 procedures:

  1. Set the altitude selector (ASEL) and leave VNAV.
  2. Bring the thrust levers to idle and select FLCH.
  3. Extend the speedbrake.
  4. Fly maximum speed, or hold the current speed if structural damage is suspected.

The descent uses FLCH rather than vertical speed because in VS mode the thrust levers would advance. The PM calls out every 10,000 ft. At "2,000 ft to level off" 250 kt is selected, and at "1,000 ft to level off" the speedbrake is retracted. Once level, the LSP calls the senior cabin attendant to the flight deck (see decompression).

Other immediate actions

Several other events are handled by hand first and by the book afterward:

Frequently asked questions

What are the memory items on the Embraer E190?

In the E190 and E190-E2 procedures described here, recall items open a short list of checklists: smoke, fire or fumes (oxygen masks on at 100 %, then crew communication), abnormal engine start (START/STOP selector to STOP), a jammed elevator or aileron (pull the disconnect handle) and steering runaway (steer disconnect pressed). The first-generation E190 adds pitch and roll or yaw trim runaway. Rejected takeoff, windshear, TCAS and upset maneuvers are also flown without the book. The operator's QAC and QRH govern.

What is the quick access checklist (QAC) on the E-Jet?

In one E-Jet operator's documents the QAC is a short card of time-critical procedures: abnormal engine start, cabin altitude high, emergency descent, battery overtemperature, dual engine failure, APU and cargo fires, jammed controls, smoke, and engine fire, severe damage or separation. On the ground the right-seat pilot reads and the left-seat pilot acts, without confirming vital items; in flight the pilot monitoring reads and the pilot flying acts. The referenced QRH checklist follows.

When is an E190-E2 takeoff rejected above 80 kt?

Above 80 kt the takeoff is in the high-energy regime, and one operator's procedures reject only for an engine failure, a fire, a condition that makes the airplane unflyable, such as flaps retracting or spoilers extending, or pilot incapacitation. On a short runway or in low visibility the crew is go-minded. After a rejection above 80 kt maximum reverse is used, reduced to idle reverse at 60 kt and closed at 30 kt; below 80 kt only idle reverse is used.

What does an E190-E2 crew do after a windshear warning?

The warning is three aural WINDSHEAR calls with a master warning, given for a decreasing headwind, a tailwind or a downdraft between 10 and 1,500 ft above the ground. The pilot flying moves the thrust levers to maximum and presses TO/GA; the autopilot disconnects, reserve thrust comes in and the flight director gives escape guidance, wings level, with pitch limited to the stick shaker angle. Flaps and gear stay where they are, and the pilot monitoring calls out any descent.

How is an emergency descent flown on the E190-E2?

In one operator's technique the crew set the altitude selector, leave VNAV, bring the thrust levers to idle, select FLCH, extend the speedbrake and fly maximum speed, or hold the current speed if structural damage is suspected. FLCH is chosen because in vertical speed mode the thrust levers would advance. The pilot monitoring calls every 10,000 ft; at 2,000 ft to level off 250 kt is selected, and at 1,000 ft to level off the speedbrake is retracted.

Does the E190-E2 have a pitch trim runaway procedure?

No. On the E190-E2 trim inputs act mainly through the elevator, and the stabilizer moves only to unload it, so Transport Canada's operational evaluation report lists the pitch trim runaway procedure, and the roll and yaw trim runaway procedure, as removed for the E2. On the first-generation E190 the recall items remain: press and hold the autopilot disconnect button, then push in the pitch trim system 1 and 2 cutout buttons.

Test yourself on Embraer E-Jet Memory Items

The v1prep banks cover this topic in the E-Jet type-rating bank, with a worked explanation for every answer. EASA ATPL, PPL, IR and CPL, the FAA written tests and type ratings for the A320, A330, A350, 737, 767, 777, A220, 787, ATR 72 and E-Jet.

Start practicing →
15,000+ questions · EASA & FAA · Free to start

Library articles are written for study and exam preparation. They do not replace your aircraft's approved documentation, your operator's procedures or the regulations themselves.