Bounced and Hard Landings
A bounced landing is a touchdown after which the airplane becomes airborne again; a hard landing is one whose vertical speed or loads may have exceeded what the landing gear and its supporting structure were designed to absorb. A bounce calls for a recovery or a go-around, a hard landing for a report and an inspection.
A landing can still go wrong in its last few seconds after a perfect approach. A bounced landing is a touchdown after which the airplane leaves the runway again, because it arrived with too much vertical speed, met the ground nose first, or still had lift in hand. A hard landing is one in which the vertical speed or the loads at touchdown may have exceeded what the landing gear and its attachments were designed to absorb. The two are linked: a hard first contact often causes the bounce, and a badly handled bounce often ends in a harder second touchdown.
What the pilot must do differs. A bounce is a handling problem, solved within seconds: hold or re-establish the landing attitude and cushion a small bounce with power, or go around from a large one. A hard landing is an airworthiness problem: the crew must report it so that the airplane is inspected before it flies again. The flare and touchdown themselves are covered in landing technique and crosswind operations.

Terms
| Term | Meaning |
|---|---|
| Balloon | The airplane rising in the flare instead of settling, typically after an over-rotation or a gust |
| Bounced landing | A touchdown after which the airplane becomes airborne again |
| Porpoising | A series of bounces with the nose pitching up and down, each cycle larger: a pilot-induced oscillation near the ground |
| Hard landing | A touchdown whose vertical speed or loads may exceed the structural design case; it must be reported |
| Rejected landing | A go-around close to the runway, which the FAA's AIM calls a balked or rejected landing; it can start after the wheels have touched |
| Hard landing inspection | The conditional inspection the aircraft maintenance manual (AMM) requires after a reported hard or heavy landing |
Causes of hard and bounced landings
Most hard and bounced landings begin with the wrong energy at the flare: too high a sink rate, too much speed, or a flare started too early or too late.
- High sink rate. An unstable approach carries a high rate of descent close to the ground, more than the flare can absorb. Unstabilized approaches figure in hard and bounced landings as well as in overruns (see stabilized approach).
- Misjudged flare height. Runway illusions mislead the eye. A runway wider than the pilot is used to makes the airplane seem too low, so the pilot rounds out too high and risks stalling onto the runway or landing heavily. A narrower runway gives the opposite errors: a low approach and a late round-out (see visual illusions).
- Excess speed. In ground effect the induced drag falls, so surplus speed bleeds off slowly and the airplane floats. A pilot who then pushes it onto the runway risks touching down on the nose wheel, a common start of a bounce.
- Wrong attitude or drift. The main wheels should touch first. Landing nose first or tail first, with drift, or above the maximum landing mass overstresses the gear and the structure behind it, even at a moderate sink rate.
- Forward center of gravity. Flaring takes more up-elevator, and with the CG forward of its limit the elevator may run out of travel before the landing attitude is reached, so the airplane touches down nose first.
- Power taken off abruptly. In a propeller airplane flaring with high power, the slipstream adds lift over the wing behind the propeller. Closing the throttle suddenly removes that lift and can drop the airplane onto the runway.
- Wind. Gusts and wind shear change the airspeed in the flare. Beneath a shower or storm cloud, a sudden gain of speed and a balloon above the path may be the first side of a microburst, with the downdraft and tailwind still to come: go around at once.
The landing gear itself is designed against bouncing: in the oleo-pneumatic strut, compressed gas carries the weight, oil forced through an orifice turns the touchdown energy into heat, and a recoil valve slows the extension stroke (see landing gear layouts and shock absorbers). Too much vertical speed overwhelms it, and a touchdown on the nose wheel pitches the nose up; with flying speed in hand, the wing then takes the airplane back into the air.
Recovering from a bounce
After a light bounce the airplane is only a few feet up with flying speed. The pilot holds, or re-establishes, the normal landing attitude, adds a little power to cushion the next touchdown and lets the airplane settle onto the main wheels. Two instinctive reactions make things worse. Pushing the nose down to "put it back on the runway" brings a nose-first impact and the start of a porpoise. Pulling the nose up to soften the second contact raises the angle of attack at a falling speed, toward a stall or a tail strike.
Pitch attitude is limited near the runway. On the A320 family the pilot monitoring calls "PITCH, PITCH" during the landing if the pitch reaches 10° or approaches the tail strike limit, and from 400 ft radio height the PFD shows a tail strike pitch limit indicator, a fixed value for the main gear compressed. On 737 NG models fitted with a tail skid, the skid's shoe is what meets the runway in an over-rotation (see tailstrike prevention).
A high bounce, or any bounce with the speed falling away, calls for a go-around. Landing again from it means meeting the runway slow and nose-high, which turns a bounce into a hard landing or a tail strike.
Exam tip: light bounce: landing attitude plus a little power, let it settle. High bounce: go around. Never chase a bounce with large nose-down inputs.
Go-around after a bounce
A go-around from a bounce is a rejected landing flown from very low height, sometimes after the wheels have already touched. It differs from a go-around at decision height in three ways.
There is a point of no return. Once the crew have committed to stopping, the landing must be completed. The landing roll procedure of the Boeing 737 NG FCOM carries the warning: "After the reverse thrust levers are moved, only a full stop landing can be made." A bounce that will end in a go-around must therefore be recognized before reverse is selected.
The systems may already be in landing mode. On the 737 NG the automatic speed brake raises the spoilers at touchdown; if either thrust lever is then advanced, the SPEED BRAKE lever moves to DOWN by itself and all spoiler panels retract, and the autobrake disarms, except during the first 3 seconds after touchdown. Automatic thrust can behave differently too: Transport Canada's evaluation of the A220 stresses that after more than 2 seconds on the ground the autothrottle does not engage automatically with TOGA, and FAA reports for the Boeing 777, 767-2C and 767-400ER require training in thrust lever behavior in rejected landings, including after touchdown.
The gear stays down until the airplane climbs. A bounce can unload the air/ground sensors, so the gear lever stays down until the altimeter shows that the airplane is actually climbing; the sensors alone are not trusted. In the 737 NG procedure the pilot monitoring calls "POSITIVE RATE" and the pilot flying then calls "GEAR UP", after TO/GA and flaps 15. In a light airplane full power comes first, then the flap comes up a stage at a time as speed and climb increase; raising full flap in one movement at low speed takes lift away abruptly and the airplane sinks.
Certification provides the performance. The landing climb requirement, the baulked landing of European texts, assumes a go-around from close to the runway with gear down and landing flap; for EASA Class B multi-engine airplanes the exam figure is a 2.5% gradient with all engines, at VREF, with the power available 8 seconds after the levers are moved (see approach speeds and go-around climb requirements).
Porpoising and pilot-induced oscillation
Porpoising is a bounce that the pilot keeps alive. The airplane meets the runway nose first and bounces, the pilot pushes to stop the climb, the nose wheel strikes again and the next bounce is higher. It is a pilot-induced oscillation (PIO), and so close to the runway there is no room for it to damp out by itself.
The mechanism is timing. The short-period pitch oscillation of an airplane runs at a rate close to the pilot's own reaction time, so a correction can easily arrive out of phase and feed the oscillation instead of damping it. The cure is to stop chasing it: set the landing attitude and hold it. For a mild porpoise the FAA's Airplane Flying Handbook gives the bounce recovery, the landing attitude with enough power to soften the next contact; for a severe one it calls for an immediate go-around.
Warning: a porpoise grows with each cycle and can end with the nose wheel striking the runway or in a hard landing. If the first correction has not stopped it, go around.
Hard landing reports and inspections
A firm landing is not a hard landing. The firm landing technique aims for a positive, intentional contact in the touchdown zone: the wheels spin up and take the weight straight away, so the ground spoilers, autobrake and anti-skid start working early, which matters most on a wet or contaminated runway. It stays within the design loads.
A hard landing is defined by loads. The design case for transport airplane landing gear is a rate of descent at touchdown of 10 ft/s (3.05 m/s) with the airplane at its maximum landing mass. Exceeding either the sink rate or the mass can damage the gear and the structure around it, and so can landing with drift or in an abnormal attitude. This is why the maximum landing mass is lower than the maximum takeoff mass, and why an overweight landing is followed by an inspection. The A320 limitations, for example, allow one only in exceptional cases, an in-flight turnback or diversion, with the overweight landing procedure (see overweight landing).

The hard landing inspection is a conditional inspection set by the AMM. ATPL texts divide the airframe into primary areas, which take the landing loads first: the landing gear and its supporting structure in the wings and fuselage, the wing to fuselage and tailplane attachments, and the engine mountings. The secondary areas, the upper and lower fuselage structure, need inspecting if damage is found in the primary ones. After a 737 NG tail strike, the FCOM wants the tail skid cartridge's warning decal read as soon as possible, before the skirt fairing sags back out and falsifies it.
The inspection only happens if the event is reported. The crew writes a suspected hard or heavy landing into the technical log; in US airline operations, 14 CFR 121.563 makes the pilot in command responsible for getting every mechanical irregularity into the maintenance log at the end of the flight time. Flight data monitoring backs this up: EASA requires an FDM program for airplanes above 27,000 kg maximum certificated takeoff mass (ORO.AOC.130), and FDM and the FAA's voluntary FOQA programs (AC 120-82) look for exceedances such as hard landings. Neither replaces the crew's report.
A hard landing can also set off the emergency locator transmitter: after an unusually hard landing, the FAA's AIM recommends monitoring 121.5 MHz before engine shutdown for the ELT's sweeping tone.
Whether the event is an accident depends on its result, not on the sink rate. Under 49 CFR 830.2, damage limited to the landing gear, wheels, tires, flaps, brakes or wingtips is not substantial damage, whereas damage that affects structural strength, such as a buckled firewall, is. A passenger hospitalized for more than 48 hours, starting within 7 days, is seriously injured. An accident must be notified to the NTSB immediately under 830.5 and reported on Form 6120.1 within 10 days under 830.15. ICAO Annex 13 uses similar tests, and in the EU an occurrence report is due within 72 hours under Regulation (EU) No 376/2014 (see accident and incident investigation).
Prevention
Hard and bounced landings are prevented long before the flare.
- Fly a stabilized approach, and go around when it is not. Research for the Flight Safety Foundation showed that crews broke off only about 3% of unstable approaches with a go-around (see go-around and missed approach).
- Cross the threshold at the planned speed. About 10% too fast adds roughly 20% to the landing distance and invites a float in ground effect, which sets in within about one wingspan of the runway.
- Flare at the right height and by the right amount. On the A320 the flare starts at about 30 ft when the approach is stabilized: raising the pitch by about 4° brings the flight path to about -1° and costs about 10 kt, and the thrust levers are closed to idle, with an automatic "RETARD" call at 20 ft as a reminder in a manual landing. The FCTM warns against letting the airplane float or prolonging the flare in search of a perfectly smooth touchdown.
- Train the recovery. US Part 121 pilots practice recovery from a bounced landing in a Level C or higher full flight simulator as part of extended envelope training (14 CFR 121.423), and must have done so within the preceding 36 calendar months.
Frequently asked questions
What should you do after a bounced landing?
It depends on the size of the bounce. After a light bounce, hold or re-establish the normal landing attitude, add a little power to cushion the next touchdown and let the airplane settle. Do not push the nose down, which risks a nose-first impact and porpoising, and do not pull it up, which risks a stall or a tail strike. After a high bounce, go around: a second attempt would meet the runway slow and nose-high.
What counts as a hard landing?
A hard landing is a touchdown whose vertical speed or loads may have gone beyond what the landing gear and its attachments were designed to absorb. For transport airplanes the design case is a descent rate of 10 ft per second, 3.05 m/s, at the maximum landing mass. Landing with drift, nose first or above the maximum landing mass can overstress the structure too. Any suspected hard landing is reported so that maintenance inspects the airplane.
What is porpoising during landing?
Porpoising is a series of bounces in which the nose pitches up and down along the runway and each cycle grows. It usually starts with a touchdown on the nose wheel, and it is kept going by the pilot's own corrections, which arrive out of step with the motion: a pilot-induced oscillation close to the ground. A slight porpoise is handled like a bounce, with landing attitude and power; a severe one calls for an immediate go-around.
Can you go around after the wheels have touched the runway?
Yes, as long as the crew has not committed to stopping. On the Boeing 737 NG that point is the reverse thrust levers: once they have moved, the FCOM allows only a full stop landing. Before then, systems may already be acting as for a landing: advancing a thrust lever retracts the 737's spoilers, and on the A220 the autothrottle does not engage with TOGA after more than 2 seconds on the ground. FAA reports for the 777 make thrust lever behavior after touchdown a training item.
What happens after a hard landing is reported?
The crew writes it up in the technical log, and the aircraft maintenance manual sets a conditional inspection before the next flight. It starts with the primary areas, the landing gear and its supporting structure, the wing and tailplane attachments and the engine mountings, and extends to the fuselage structure if damage is found. Operators' flight data monitoring programs also flag heavy landings, but they do not replace the crew's report.
Is a hard landing an aircraft accident?
Only if it kills or seriously injures someone, or causes substantial damage. Under the NTSB's 49 CFR 830.2, damage limited to the landing gear, wheels, tires, flaps, brakes or wingtips is not substantial damage, whereas damage to structural strength such as a buckled firewall is. A passenger hospitalized for more than 48 hours, starting within 7 days, also makes it an accident, to be notified to the NTSB immediately.
Test yourself on Bounced and Hard Landings
The v1prep banks cover this topic in Operational Procedures (070), with a worked explanation for every answer. EASA ATPL, PPL, IR and CPL, the FAA written tests and type ratings for the A320, A330, A350, 737, 767, 777, A220, 787, ATR 72 and E-Jet.
Start practicing →Sources and further reading
- FAA Airplane Flying Handbook (FAA-H-8083-3C), Chapter 9, Approaches and Landings
- 14 CFR 121.423, Pilots, extended envelope training
- EASA Easy Access Rules for Air Operations, ORO.AOC.130 (flight data monitoring)
- 49 CFR Part 830, Notification and Reporting of Aircraft Accidents or Incidents
- FAA Flight Standardization Board Report, Boeing 777, Revision 12 (draft)
- Transport Canada, Operational Evaluation Report BD-500 (A220-100 and A220-300), Revision 3
- FAA AC 120-82, Flight Operational Quality Assurance
Library articles are written for study and exam preparation. They do not replace your aircraft's approved documentation, your operator's procedures or the regulations themselves.