ATC Light Signals
ATC light signals are narrow beams of green, red or white light, steady or flashing, that an aerodrome control tower aims at an aircraft, vehicle or person it cannot reach by radio. Each signal approves or refuses the next move, and the pilot acknowledges by a set movement of the aircraft or by flashing its lights.
ATC light signals are how a control tower gives instructions to an aircraft without using the radio. The controller aims a lamp, usually called a light gun or signal lamp, at one aircraft and shows it green, red or white light, either steady or as a series of flashes. Each combination has a fixed meaning that depends on whether the aircraft is in flight or on the ground, and the pilot answers with an equally fixed movement or light.
Light signals matter whenever voice contact is missing: after a radio failure, for an aircraft that carries no radio, or for a vehicle or person on the airport without one. The code is set internationally in Appendix 1 to ICAO Annex 2 and, in Europe, in Appendix 1 to SERA. In the United States the meanings are written into regulation, 14 CFR 91.125, and expanded in AIM 4-3-13. The two tables agree on almost everything, and examinations on both sides of the Atlantic test the few places where they do not.
When light signals are used
The FAA's AIM describes light signals as the procedure a tower uses to control aircraft, ground vehicles, equipment and people that have no radio, and also those that do have one when radio contact cannot be established. The lamp produces an intense, narrow beam of a single selected color, so that it can be aimed at one aircraft.
The AIM is frank about the limits. The pilot may not be looking at the tower when the signal is sent, and a lamp can only approve or refuse what the pilot is evidently about to do. It cannot pass a runway, a wind or a traffic position. Apart from approval and refusal, the only extra message it can carry is what the AIM calls the general warning signal, which tells the pilot to be on the alert.
In practice a pilot meets light signals in a few situations:
- Radio failure in flight. Under ICAO and SERA, a flight that loses radio contact in visual conditions continues in those conditions, lands at the nearest suitable aerodrome and reports its arrival; at a controlled aerodrome it watches the tower for light signals (see radio communication failure). The transponder code 7600 tells the controller why the aircraft is silent.
- Arriving at a US Class D airport. AIM 4-2-13 asks a pilot whose radio has failed to stay outside or above the Class D surface area until the direction and flow of traffic are clear, then join the pattern and watch the tower. Under 14 CFR 91.129(d), a VFR pilot whose radio fails may land there if the weather is at or above basic VFR minimums, visual contact with the tower is kept and a clearance to land is received.
- Departing without a radio. The AIM asks a pilot whose radio fails before leaving the parking area to try to have it repaired, and otherwise to telephone the tower and ask for authorization to depart without two-way radio. If radio contact is lost after leaving the parking area, the pilot watches the tower for light signals or keeps monitoring the tower frequency.
- Receiver failure only. A pilot who can still transmit tells the tower the aircraft type, position, altitude and intention to land, and asks to be controlled with light signals.
Note: at an airport with a US Government tower where ATC has allowed a flight without two-way radio in the surface area, and at one whose tower the US Government does not operate when radio contact cannot be made, the AIM requires a clearance by light signal before taxiing on a runway, before takeoff and before landing.

Signals to aircraft in flight
The meanings for an aircraft in the air are these. ICAO and SERA describe flashing signals as a series of flashes; the FAA says flashing.
| Signal | ICAO and SERA | FAA (14 CFR 91.125) |
|---|---|---|
| Steady green | Cleared to land | Cleared to land |
| Flashing green | Return for landing; the landing clearance follows in due course | Return for landing, to be followed by steady green at the proper time |
| Steady red | Give way to other aircraft and continue circling | Give way to other aircraft and continue circling |
| Flashing red | Aerodrome unsafe, do not land | Airport unsafe, do not land |
| Flashing white | Land at this aerodrome and proceed to the apron; clearances to land and taxi follow | No meaning in flight |
| Alternating red and green | Not part of the set | Exercise extreme caution |
| Red pyrotechnic | Notwithstanding any previous instructions, do not land for the time being | Not in 91.125 |
Two pairs are easily confused. Green flashes mean come back and land later, while the clearance itself is the steady green; a pilot who lands on the flashes has landed without a clearance. Steady red only asks the pilot to keep circling and give way, while red flashes say the aerodrome is unsafe and the aircraft must not land there. In both systems, then, the steady green clears and the flashing red forbids.
Exam tip: green flashes in flight are a promise, not a clearance; wait for the steady green. Steady red means circle; red flashes mean do not land here.

Signals to aircraft on the ground
On the ground the same colors control taxiing and takeoff:
| Signal | ICAO and SERA | FAA (14 CFR 91.125) |
|---|---|---|
| Steady green | Cleared for takeoff | Cleared for takeoff |
| Flashing green | Cleared to taxi | Cleared to taxi |
| Steady red | Stop | Stop |
| Flashing red | Taxi clear of the landing area in use | Taxi clear of the runway in use |
| Flashing white | Return to the starting point on the aerodrome | Return to the starting point on the airport |
| Alternating red and green | Not part of the set | Exercise extreme caution |
The logic carries over from the air: green approves, steady red halts, flashing red tells the aircraft to get clear of the landing area or runway in use, and white sends it back where it came from. A pilot holding on the apron with a dead radio waits for green flashes before moving and for a steady green before taking off.
To be seen at night, the AIM suggests that a pilot who wants the tower's attention between sunset and sunrise switch on a landing light and taxi to a position clear of the active runway where the light is visible from the tower, leaving it on until the tower signals.
Acknowledging by day and by night
A light signal is one-way unless the pilot answers it. ICAO and SERA set the acknowledgment as follows:
| By day | By night | |
|---|---|---|
| In flight | Rock the wings, except on the base and final legs of the approach | Flash the landing lights on and off twice or, if none are fitted, the navigation lights |
| On the ground | Move the ailerons or rudder | Flash the landing lights on and off twice or, if none are fitted, the navigation lights |
The exception for base and final exists because rocking the wings low and slow on the approach would itself be a hazard. The FAA's version is close: AIM 4-2-13 asks an arriving pilot to rock the wings in daylight, a departing pilot to move the ailerons or rudder, and both to blink the landing or navigation lights at night. It adds helicopter answers: by day a hovering helicopter turns toward the tower and flashes its landing light, one in flight makes shallow banks in opposite directions, and at night it flashes the landing light or search light.

Warning: in the circuit, keep the tower in view. A signal sent while the pilot is looking elsewhere is simply lost, and the AIM lists this as the first weakness of the system.
Signals to vehicles and persons
The FAA table in AIM 4-3-13 has a third column, for the movement of vehicles, equipment and personnel on the airport:
| Signal | Vehicles, equipment and personnel (AIM 4-3-13) |
|---|---|
| Steady green | Cleared to cross, proceed or go |
| Flashing green | Not applicable |
| Steady red | Stop |
| Flashing red | Clear the taxiway or runway |
| Flashing white | Return to the starting point on the airport |
| Alternating red and green | Exercise extreme caution |
The meanings mirror those for aircraft on the ground, except that flashing green, the taxi clearance, is marked not applicable to vehicles. The AIM uses the lamp for vehicles without radio and for those with radio when contact cannot be established. The ICAO and SERA table has no such column: its signals are addressed to aircraft in flight and on the ground.
Pilots should not confuse these signals with the lights vehicles carry themselves. Under ICAO Annex 14, a vehicle on the movement area shows a low-intensity flashing yellow light, and emergency vehicles responding to an emergency add flashing blue lights (see obstacles and obstacle limitation surfaces). The hand signals used to guide aircraft on the apron are a separate code again (see marshaling signals).
Ground signals and other visual signals
A light gun speaks to one aircraft. The signal area, a square laid out where pilots can see it from the air, speaks to every pilot arriving without radio. The landing T shows the direction for landing and takeoff, along its shaft toward the crossarm; a right-hand arrow means right-hand circuits; a red square with one yellow diagonal calls for special care because of the state of the maneuvering area; a red square with two yellow diagonals prohibits landing, a prohibition liable to be prolonged; a white dumb-bell confines aircraft to runways and taxiways; and a double white cross means gliders are flying. The full set is described in interception and visual signals.

Several other visual codes look similar and are examined alongside the tower's:
- Search and rescue. An aircraft shows survivors that it has understood their ground signal by rocking its wings by day, or flashing its landing lights on and off twice at night, the same movements used for the tower.
- Interception. An intercepted aircraft acknowledges "you have been intercepted, follow me" by rocking the aircraft, flashing its navigation lights at irregular intervals and following. Irregular flashing of all lights means distress.
- Urgency and distress. Repeatedly switching the landing lights on and off is the urgency signal. SOS in Morse by light, red rockets or shells fired at short intervals, or a red parachute flare signal distress (see distress and urgency communications).
- Aerodrome beacons. A beacon at a land aerodrome flashes white, or alternately white and green, for every pilot in range. A light gun's beam is aimed at one aircraft.
ICAO and FAA differences
| Point | ICAO and SERA | FAA |
|---|---|---|
| Legal home | Appendix 1 to Annex 2 and to SERA | 14 CFR 91.125, with AIM 4-3-13 and 4-2-13 |
| Flashing white in flight | Land here and proceed to the apron | No meaning |
| Alternating red and green | Not used | Exercise extreme caution, in flight, on the ground and for vehicles |
| Red pyrotechnic | Do not land for the time being, whatever was said before | Not in the regulation |
| Flashing red on the ground | Taxi clear of the landing area in use | Taxi clear of the runway in use |
| Vehicles and personnel | No column in the light signal table | A column of meanings in AIM 4-3-13 |
| Night acknowledgment | Landing or navigation lights flashed twice | Landing or navigation lights blinked |
For a pilot, the practical rule is the same everywhere: after a radio failure near a controlled aerodrome, squawk 7600, keep the tower in sight, take nothing for granted until the steady green, and answer every signal. EASA air law and communications papers ask for the ICAO and SERA meanings, including the white flashes, while the FAA private pilot test asks for the 91.125 table, including alternating red and green. A pilot who flies under both systems learns the shared core once and the differences as a short list.
Frequently asked questions
What does a flashing green light from the tower mean?
To an aircraft in flight, a series of green flashes means return for landing. It is not a landing clearance; that comes later as a steady green light. To an aircraft on the ground, green flashes mean cleared to taxi, while a steady green means cleared for takeoff. The meaning is the same under ICAO, SERA and the FAA's 14 CFR 91.125.
What does a steady red light mean in aviation?
Aimed at an aircraft in flight, a steady red light means give way to other aircraft and continue circling. Aimed at an aircraft on the ground, it means stop. In the FAA table it also means stop for vehicles, equipment and people on the airport. Red flashes are the stronger signal; in flight they mean the aerodrome is unsafe and the pilot must not land.
How do you acknowledge a light signal from the tower?
In flight by day, rock the wings, though ICAO and SERA do not expect this on the base and final legs. At night, flash the landing lights on and off twice, or the navigation lights if no landing lights are fitted. On the ground by day, move the ailerons or rudder, and at night use the same light signal. The FAA's AIM gives the same movements and blinking the landing or navigation lights.
What does an alternating red and green light mean?
Alternating red and green is an FAA signal meaning exercise extreme caution. It has the same meaning for aircraft in flight, aircraft on the ground and vehicles, equipment and people on the airport. It is not part of the ICAO and SERA set of light signals, which European exams test, so a pilot flying in both systems learns it as an American addition.
What does a flashing white light from the tower mean?
On the ground, white flashes mean return to the starting point on the aerodrome, in both the ICAO and FAA tables. In flight the two differ. Under ICAO and SERA, white flashes tell the pilot to land at this aerodrome and proceed to the apron, with the clearances to land and taxi to follow. In 14 CFR 91.125 a flashing white light has no meaning for an aircraft in flight.
Test yourself on ATC Light Signals
The v1prep banks cover this topic in Air Law (010), with a worked explanation for every answer. EASA ATPL, PPL, IR and CPL, the FAA written tests and type ratings for the A320, A330, A350, 737, 767, 777, A220, 787, ATR 72 and E-Jet.
Start practicing →Sources and further reading
- 14 CFR 91.125, ATC light signals
- FAA Aeronautical Information Manual, Chapter 4 Section 3, Airport Operations (4-3-13, Traffic Control Light Signals)
- FAA Aeronautical Information Manual, Chapter 4 Section 2, Radio Communications Phraseology and Techniques (4-2-13)
- 14 CFR 91.129, Operations in Class D airspace
- UK CAA Regulatory Library, SERA Appendix 1, Signals for aerodrome traffic
- EASA Easy Access Rules for Standardised European Rules of the Air (SERA)
- ICAO Annex 2, Rules of the Air (Appendix 1, Signals)
Library articles are written for study and exam preparation. They do not replace your aircraft's approved documentation, your operator's procedures or the regulations themselves.