Skip to content

Jet Flight Planning with CAP 697 Cruise Tables

Flight PlanningATPL10 min readUpdated Nov 2026
Definition

CAP 697 is the manual of flight planning data that the UK Civil Aviation Authority wrote for the European pilot theory examinations. Its medium-range jet transport (MRJT) section gives climb, cruise, integrated range and descent tables and simplified planning charts from which ATPL candidates work out jet fuel and time.

Jet flight planning in the EASA ATPL theory exams is done by hand, from a book. The book is CAP 697, the flight planning manual the UK Civil Aviation Authority wrote for the JAR-FCL examinations. Its section for a medium-range jet transport, the MRJT, holds the climb, cruise and descent data from which candidates work out trip fuel, flight time and the masses at each point of the flight. The principles are simple; the common errors are misread tables, ground miles entered as air miles and forgotten corrections.

This article explains how the jet cruise data are organized and read. It does not reproduce the manual's tables: in the exam every value comes from the copy of CAP 697 in front of the candidate. The climb and descent tables are covered in climb and descent planning.

The MRJT reference aircraft

The manual describes three invented aircraft, which gives every candidate an identical set of numbers to work from: the SEP1 single-engine piston airplane, the MEP1 twin piston airplane and the MRJT medium-range jet transport. The performance questions draw on the same three aircraft in a second manual, CAP 698, and mass and balance questions work the MRJT's center of gravity in percent of the mean aerodynamic chord. The manuals remain in use: the Swedish Transport Agency, for example, lists CAP 696, CAP 697 and CAP 698 among the items permitted during its CPL, IR and ATPL theory examinations.

Because the MRJT is not a real type, figures from a real airliner's manuals do not apply to it. Its piston siblings are planned mostly from graphs; the jet is planned mostly from tables. Detailed jet planning uses three table sets:

Table What it gives Entered with
En-route climb Time, fuel and air distance from sea level to each cruising level Mass at the start of the climb, temperature deviation
Cruise and integrated range TAS, fuel flow, specific air range and cumulative air distance Pressure altitude, temperature deviation, gross mass
Descent Time, fuel and air distance from top of descent to the end of descent Landing mass

Alongside them sit simplified planning charts for quicker answers and charts for fuel tankering. Every table and chart states the conditions it was built for, such as speed schedule, configuration and temperature. Reading those conditions comes first, because an answer is only valid for a flight flown the same way.

Long range cruise and integrated range tables

Maximum range cruise is the speed at which each kilogram of fuel carries the airplane furthest through the air. The curve of specific air range against speed is flat near its peak, so a little more speed costs very little range. Long range cruise (LRC) takes advantage of this: it is the speed slightly above maximum range cruise at which the specific air range has dropped to 99 percent of its maximum. One percent of range buys a useful increase in speed. ATPL explanations give LRC for a typical medium-range jet as about M 0.74 when the airplane is within 2,000 ft of its optimum altitude. Planning data commonly tabulate a faster constant Mach number as well, such as M 0.78, at a higher fuel burn. LRC itself is not one fixed Mach number: it rises slightly as mass increases.

Long range cruise on the drag curve: a little faster than the maximum range speed of about 1.32 VMD, it keeps 99 percent of the best specific range and gains speed in return. v1prep schematic.
Long range cruise on the drag curve: a little faster than the maximum range speed of about 1.32 VMD, it keeps 99 percent of the best specific range and gains speed in return. v1prep schematic.Illustration © v1prep

An integrated range table deals with a problem that a single fuel flow figure handles badly. A jet's specific air range improves as it gets lighter, so the fuel needed for each nautical air mile changes all the way through the cruise, and a fuel flow read at one mass does not hold for the whole segment. For one pressure altitude and temperature deviation, the table lists still-air cruise performance against gross mass:

The cumulative column is the one that matters. The difference between the figures for any two masses is the air distance flown while burning the fuel between them. The planner looks up the figure for the starting mass, then finds the lighter mass whose figure lies exactly one sector air distance away; that mass is where the cruise ends. The difference between the two masses is the cruise fuel.

The table holds no groundspeed, because the wind is not part of it. The sector's ground distance must first be converted to air distance with NAM ÷ NGM = TAS ÷ GS, which holds because the airplane covers both distances in one and the same flight time; the sector time is ground distance divided by groundspeed. As a cross-check, the cruise fuel divided by the time should come close to the fuel flows the table lists for the masses in between (see time, speed, distance and fuel calculations).

Exam tip: enter the cruise tables with air distance, never ground distance, and work out the time with groundspeed, never TAS. A headwind means more air miles than ground miles; a tailwind fewer.

ISA deviation and mass corrections

Temperature. Warm air is thinner than standard air, and both the engines and the wing perform less well in it, so jet cruise data are indexed by ISA deviation as well as level and mass (see international standard atmosphere). At a constant Mach number, temperature also changes the true airspeed. The local speed of sound is set by absolute temperature alone, at about 38.94 × √T knots with T in kelvin. At FL350 the ISA temperature, at 2 °C per 1,000 ft, is −55 °C, or 218 K, and M 0.74 is about 425 kt TAS. At ISA +10 the temperature is 228 K and the same Mach number gives about 435 kt. The warm sector is flown faster, so it takes less time, but the fuel flow must be read for the actual deviation, not borrowed from the standard-day figures. A hot atmosphere also lowers the maximum altitude, because less thrust is available.

Mass. A heavier airplane must fly at a higher angle of attack, or a higher speed, to make the extra lift, so its drag and fuel flow are higher and its specific air range lower. At a constant altitude and angle of attack, a 10 percent increase in mass costs about 5 percent of specific range: drag, and so fuel flow, rise by about 10 percent while the TAS rises by only about 5 percent. If the airplane instead cruises at the optimum altitude for each mass at a constant Mach number, the loss is closer to 10 percent. Mass also moves the optimum altitude, as described below.

Keeping track of mass. Every table is entered with a mass, so a plan is a chain of masses from brake release through top of climb, each cruise segment and top of descent to landing. It can be worked forward from the takeoff mass or backward from the landing mass, which the descent table needs anyway. An estimated landing mass is built up from the dry operating mass, the traffic load and the fuel expected on board at landing, normally the alternate fuel, the final reserve fuel and the contingency fuel, which the plan expects to remain unused (see fuel planning and fuel reserves).

Simplified flight planning charts

For quicker answers CAP 697 adds simplified flight planning charts, which give a sector's fuel and time with much less working than the three detailed table sets.

Each chart is built for a stated cruise schedule. ATPL explanations describe long range cruise, approximated as M 0.74, flown no more than 2,000 ft from the optimum altitude, a band in which the altitude costs no more than about 1 percent of specific air range. Cruising away from the optimum altitude brings a fuel penalty, which planning data give as a percentage added to the cruise fuel. The time is affected by temperature for the reason given above: at a fixed Mach number, warmer air means a higher TAS.

The MRJT section also includes charts for fuel tankering, carrying extra fuel from a cheaper station. They show what share of the extra fuel is used up by its own weight on the way, and from that the break-even price: tankering pays only when fuel at the destination costs more than this. They are valid only if the extra mass does not stop the airplane reaching its planned cruise level, since a lower level would cost more than the charts allow for (see cost index and cruise economics).

Dimly lit flight deck of an older Boeing 737 with round-dial instruments; at the bottom, left of center, is the FMS control display unit, its screen blank, with line select keys on both sides, page keys including CLB, CRZ, DES and PROG, and a keypad.
The FMS control display unit, screen off, low on the panel of an older Boeing 737 flight deck, with page keys for the climb, cruise and descent. In airline service the flight management computer and the operator's planning system do the work the CAP 697 tables teach by hand, and the crew check the results.Yuezhi Huang · CC BY-SA 4.0 · Wikimedia Commons

Step climbs and optimum altitude

The optimum altitude is the altitude that gives the best specific air range at the airplane's present mass. Below it, within the optimum range, climbing improves the air miles per kilogram; above it, range falls again. A heavier airplane has a lower optimum altitude, because it needs denser air to fly at its best-range lift coefficient. As fuel burns off, the optimum rises. Flying no more than 2,000 ft above or below it costs at most 1 percent of the best specific air range. The optimum is an economic figure, not a limit. The maximum altitude is a ceiling, reached when the airplane needs all of its maximum cruise thrust just to keep its cruise speed, and it also takes a margin against buffet (see buffet boundaries and maximum altitude).

A twin-engined airliner high in a clear blue sky, trailing white condensation trails behind its engines.
An airliner at cruise level. As fuel burns off, the level at which it flies most economically rises, which is why long sectors are planned with step climbs.Noah Wulf · CC BY-SA 4.0 · Wikimedia Commons

In theory the airplane would follow the rising optimum in a cruise climb, drifting upward continuously while holding its Mach number and lift coefficient. Air traffic control works with fixed levels, so long sectors are flown as step climbs instead, usually of 2,000 ft or 4,000 ft, 2,000 ft being the spacing between levels in the same direction in RVSM airspace (see RVSM). The arithmetic of the 2,000 ft band explains the timing of a 4,000 ft step: taken when the optimum has risen 2,000 ft above the current level, it leaves the airplane 2,000 ft above the optimum, so the flight stays inside the band before and after the step.

In the tables, a step splits the cruise into segments. Each segment is worked in the table for its own level, and the mass at the end of one is the mass at the start of the next. Wind can matter more than height. If the headwind is much weaker at a lower level, that level may give more ground miles per kilogram than the optimum, so planning compares levels using the forecast winds.

Exam tip: optimum altitude rises as mass falls. A heavy airplane starts the cruise lower, and step climbs follow the optimum up.

Worked example

A cruise segment of 1,000 NGM is flown at FL350 at M 0.74, with a 50 kt headwind component and a temperature of ISA +10. The figures are given in the question, not taken from the manual.

  1. Temperature. ISA at FL350 is 15 − (2 × 35) = −55 °C. ISA +10 is −45 °C, which is 228 K.
  2. TAS. Local speed of sound: 38.94 × √228 ≈ 588 kt. TAS = 0.74 × 588 ≈ 435 kt.
  3. Groundspeed. 435 − 50 = 385 kt.
  4. Time. 1,000 ÷ 385 ≈ 2.60 h, about 2 h 36 min.
  5. Air distance. NAM = 1,000 × 435 ÷ 385 ≈ 1,130 NAM.
  6. Cruise fuel. In the integrated range table for FL350, entered for the temperature deviation, read the cumulative air distance for the mass at the start of the segment. Move to the lighter mass whose figure is 1,130 NAM different, and read it as the end mass. Start mass minus end mass is the cruise fuel.
  7. Check. The cruise fuel divided by 2.60 h should be close to the fuel flows the table lists for the masses in between.

On a standard day the same segment would be flown at about 425 kt TAS and 375 kt groundspeed, taking about 2 h 40 min over about 1,133 NAM. The warmer air saves time, while the air distance hardly changes; it is the wind that sets the air distance.

Working backward needs a landing mass. Suppose a question gives a dry operating mass of 33,510 kg, a traffic load of 7,600 kg, alternate fuel of 1,100 kg, final reserve fuel of 983 kg and contingency fuel of 102 kg, which is 5 percent of a 2,040 kg trip fuel. The estimated landing mass is 33,510 + 7,600 + 1,100 + 983 + 102 = 43,295 kg; the trip fuel is not in it, because it is burned before landing. Adding the descent fuel gives the mass at the top of descent, the end mass of the last cruise segment; working back through the cruise and climb gives the brake release mass, which is then checked against the structural and performance limits (see takeoff mass limitations).

Warning: the classic slips are ground miles entered in the range table, TAS used for the time, the ISA deviation ignored, and sea-level values left in a climb from an elevated aerodrome.

Frequently asked questions

What is CAP 697?

CAP 697 is a book of planning graphs and tables that the UK Civil Aviation Authority produced for the JAR-FCL theory examinations, and European flight planning questions are still set on it. Its data describe three invented aircraft, the SEP1 single-engine piston, the MEP1 twin piston and the MRJT jet, so that all candidates share one set of numbers. Candidates use the manual in the exam and read their answers from it.

What is an integrated range table?

An integrated range table gives still-air cruise performance for one pressure altitude, speed schedule and temperature deviation, listed against gross mass: true airspeed, fuel flow, specific air range and a cumulative air distance. The difference between the cumulative distances for two masses is the air distance flown while the fuel between those masses is burned, so the table gives cruise fuel without averaging the fuel flow.

What is long range cruise in ATPL flight planning?

Long range cruise (LRC) is a speed slightly above maximum range cruise where the specific air range is down to 99 percent of the best value. Giving up 1 percent of range buys a useful increase in speed. ATPL explanations give LRC for a typical medium-range jet as about Mach 0.74 when the airplane is within 2,000 ft of its optimum altitude, and the Mach number rises slightly as mass increases.

Why are distances converted from NGM to NAM before using cruise tables?

Cruise and range tables are still-air data, so their distances are nautical air miles. A route is measured in nautical ground miles. The airplane covers the two distances in the same flight time, which makes NAM divided by NGM equal to TAS divided by groundspeed. With a headwind the airplane flies more air miles than ground miles and burns more fuel; entering the table with the ground distance would understate the fuel.

How does a warmer than standard atmosphere affect jet cruise planning?

Warm air is less dense, which reduces engine and aerodynamic performance, so cruise data are indexed by the deviation from ISA temperature. At a constant Mach number the true airspeed rises with the square root of the absolute temperature: at FL350, Mach 0.74 is about 425 kt TAS in ISA and about 435 kt at ISA +10. The sector takes less time, and the fuel flow must be taken for the actual deviation.

Test yourself on Jet Flight Planning with CAP 697 Cruise Tables

The v1prep banks cover this topic in Flight Planning (033), with a worked explanation for every answer. EASA ATPL, PPL, IR and CPL, the FAA written tests and type ratings for the A320, A330, A350, 737, 767, 777, A220, 787, ATR 72 and E-Jet.

Start practicing →
15,000+ questions · EASA & FAA · Free to start

Library articles are written for study and exam preparation. They do not replace your aircraft's approved documentation, your operator's procedures or the regulations themselves.