B737 Standard Callouts
Boeing 737 standard callouts are the fixed phrases the pilot monitoring and the pilot flying speak at set points of a flight, from 80 knots on the takeoff roll to 60 knots after landing, to share what the instruments show, confirm each action before it is taken and reveal a missed event or an incapacitated pilot.
Standard callouts on the Boeing 737 are fixed words spoken at fixed moments of a flight. Most are made by the pilot monitoring (PM) and answered, or acted on, by the pilot flying (PF). They tell the other pilot what an instrument shows or what has just happened, make sure both pilots share one picture before anything is done, and, by their absence, warn that something is wrong with the airplane or the other pilot.
The callouts described here are those of a 737 NG flight crew operations manual (FCOM), which gathers them in two places: a standard callouts table (section NP.40) for the climb, descent and approach, and the amplified normal procedures (NP.21), which build the takeoff, go-around and landing roll calls into the actions themselves. The NG and the MAX share one FAA type rating, B-737, and MAX differences are noted where they matter. Wording and heights in an operator's own manual can differ from those quoted here; the operator's FCOM governs.
Purpose of standard callouts
Boeing divides crew work two ways. Preflight and postflight duties go by seat, to the captain and the first officer; phase of flight duties go to the PF and the PM, whichever seat each occupies. The PF taxis, controls the flight path and airspeed, sets the airplane's configuration and navigates. The PM reads checklists, works the radios, carries out whatever the PF requests and watches over the taxi, flight path, airspeed, configuration and navigation. The captain remains the final authority for every task directed and done. Some older texts, among them several recall item descriptions, still say pilot not flying (PNF).
The callout philosophy has three steps. The PM makes each callout from instrument indications or from what is observed. The PF checks the condition on their own instruments and acknowledges. If the PM does not make a required callout, the PF makes it. A callout that does not come when expected is information in itself: it may point to a failed system or indication, or to an incapacitated crewmember.
The same rule covers automatic voice callouts. When an electronic callout sounds on the approach, the PF acknowledges it; when an expected one does not sound, the PM says it. Below 10,000 ft unnecessary conversation is prohibited, and casual talk is avoided in every critical phase, above all taxi, takeoff, approach and landing.
The automation is shared on the same lines. The mode control panel (MCP) belongs to the PF, who, when hand flying, asks the PM to make the changes. CDU entries in flight are normally the PM's, and nothing entered is executed until the second pilot has checked it.
Takeoff callouts
The takeoff roll starts with the thrust levers brought to about 40% N1; once the engines are stable, TO/GA is pushed and the correct takeoff thrust checked, with any adjustment made before 60 kt. From then until V1 the captain's hand stays on the thrust levers, whoever is flying.
| Moment | Pilot monitoring | Pilot flying |
|---|---|---|
| 80 kt | "80 KNOTS" | Checks the speed, "CHECK" |
| V1 | Verifies the automatic "V1" callout, or calls "V1" | |
| VR | "ROTATE" | Rotates toward a 15° pitch attitude |
| Climb shown on the altimeter | "POSITIVE RATE", then sets the gear lever UP | Verifies the climb, "GEAR UP" |
| Acceleration height | Sets the flap lever as directed | "FLAPS [number]" on the retraction schedule |
Once above 400 ft radio altitude, the PF asks for a roll mode if one is needed, and the roll mode and VNAV engagement are checked. When the flaps are up, the gear lever of the NG goes to OFF once retraction is complete. The 737-8's lever has only two positions, so that step disappears; the FSB lists the new lever as a procedure change from the 737-800.
If the takeoff is rejected, the QRH has the captain call "REJECT" and then at once close the thrust levers, disengage the autothrottle and brake, all together, before raising the SPEED BRAKE lever and selecting reverse. The first officer's part is to verify those actions, call what the SPEED BRAKE lever shows, "SPEEDBRAKES UP" or "NO SPEEDBRAKES", and call "60 KNOTS" in the rollout. See B737 memory items.
Climb and descent callouts
The FCOM table gives the PM four altitude calls:
| Point | PM callout |
|---|---|
| Approaching the transition altitude or level | "TRANSITION, ALTIMETERS RESET" |
| 1,000 ft above or below the assigned altitude or flight level (IFR) | "1000 FT TO LEVEL OFF" |
| 10,000 ft MSL in descent, where the speed is reduced | "10000 FT" |
| 1,000 ft above the initial approach altitude (IFR) | "1000 FT ABOVE INITIAL" |
The altimeters are set to standard and cross-checked when climbing through the transition altitude, and set and cross-checked again when descending below the transition level. The Descent procedure is completed by 10,000 ft MSL and ends with the call "DESCENT CHECKLIST".
Flight mode annunciation callouts
The flight mode annunciations (FMA) show the engaged and armed autothrottle, roll and pitch modes and the autopilot or flight director status. Engaged autothrottle modes, such as N1, MCP SPD or RETARD, appear in green and ARM in white; CWS R, CWS P and SINGLE CH appear in amber. For 10 seconds after each engagement a rectangle is drawn around the new pitch, roll, autopilot status or thrust mode, and around a CWS mode it flashes.
A selection on the MCP is only a request. The FCOM asks the crew to check that each selected value changes on the flight instruments, and describes announcing changes on the FMA and the thrust mode display, as they occur, as good CRM practice. The flight mode annunciation callout is that announcement: the pilot who sees the change says what the FMA now shows, and the other checks it.
Some changes come without any input. With APP armed, the roll column shows VOR/LOC and the pitch column G/S, both armed. On a dual-autopilot ILS, below 1,500 ft radio altitude FLARE armed is annunciated and SINGLE CH disappears; in an autoland the autothrottle shows RETARD from about 27 ft. During the preflight, once the IRS have aligned, the autothrottle, roll and pitch fields should be blank and the AFDS status FD. See B737 autopilot flight director system.

Approach callouts and minimums
The FCOM table gives the PM the approach callouts:
| Event | PM callout |
|---|---|
| First positive inward motion of the localizer (IFR) | "LOCALIZER ALIVE" |
| First positive motion of the glideslope (IFR) | "GLIDE SLOPE ALIVE" |
| Final fix inbound, with altimeter, instrument and flag cross-check (IFR) | "OUTER MARKER" (or VOR, NDB and so on), the time and altitude, "ALTIMETERS AND INSTRUMENTS CROSS CHECKED" |
| 1,000 and 500 ft above field elevation | "1000", "500" |
| 500 ft above field elevation, autoland only | "AUTOLAND STATUS" |
| 100 ft above the DH, DA or MDA (IFR) | "APPROACHING MINIMUMS" |
| Visual descent point | "VISUAL DESCENT POINT" |
| DH or DA reached, or missed approach point (IFR) | "MINIMUMS" |
The minimums callout splits the task: the PM calls the altitude and the PF, looking for the runway, announces the decision. With the visual reference established the PF calls "LANDING"; without it, "GO AROUND". The FCOM defines visual reference as the first approach lights, threshold lights or other markings identifiable with the approach end of the runway, clearly visible, with the airplane's position and flight path such that the approach and landing will succeed. The regulations set the minimum: in the United States, outside CAT II and III, 14 CFR 91.175 requires at least one listed reference for the runway to be distinctly visible and identifiable, and approach lights by themselves do not permit descent below 100 ft above the touchdown zone elevation without the red terminating bars or red side row bars also in view.
On an ILS the configuration calls follow the beam. When the glideslope comes alive the PF calls "GEAR DOWN" and "FLAPS 15", and the PM selects gear down, confirms the green gear lights, selects flaps 15, sets the engine start switches to CONT and the speed brake lever to ARM. When the glideslope is captured, the PF calls the landing flap setting, which the PM selects, and the missed approach altitude goes into the MCP. With integrated approach navigation (IAN) the call "APPROACHING GLIDE PATH" comes about 2 NM before the final approach fix, together with "GEAR DOWN" and "FLAPS 15", and crossing the fix the two altimeters have to agree within 100 ft. For an autoland the AFDS status is checked at 500 ft; from there down, on a dual-autopilot ILS, the AUTOLAND warning light flashes red on an autopilot disengagement, a stabilizer trim warning or an ILS deviation below 200 ft.
Automatic altitude callouts
On most variants the GPWS calls the radio altitude at 2,500, 1,000, 500, 400, 300, 200, 100, 50, 40, 30, 20 and 10 ft. It also calls "APPROACHING MINIMUMS" 80 ft above, and "MINIMUMS" at, the DH or MDA set on the captain's MINS selector, using radio altitude with the selector at RADIO and barometric altitude at BARO. Honeywell's guide adds that each callout is given only once per approach and that the minimums callouts need the landing gear down. On airplanes with the Smart 500 callout, "FIVE HUNDRED" is given on an approach other than an ILS or GLS, on a back course, with Glideslope Cancel selected, or when the airplane is more than 2 dots off the localizer or glideslope. As the airplane passes below the selected minimums, the minimums reference on the PFD changes to amber and flashes for 3 seconds.
Exam tip: the FCOM table places the crew's "APPROACHING MINIMUMS" 100 ft above the minimums; the automatic GPWS callout on most variants comes 80 ft above.
Go-around callouts
The go-around runs as an exchange of calls:
| Step | Pilot flying | Pilot monitoring |
|---|---|---|
| Initiation | Pushes TO/GA, confirms the thrust rising, "FLAPS 15" or the setting needed | Moves the flap lever, watches the flaps travel |
| Climb established | "GEAR UP" | Confirms the go-around attitude, "POSITIVE RATE" |
| Thrust | Confirms or adjusts go-around thrust, "THRUST SET", then gear lever UP and missed approach altitude checked |
Bank stays within 15° while the airspeed is in the amber band. Climbing through 400 ft radio altitude the roll mode is chosen and its annunciation confirmed, at acceleration height the PF calls the flaps up on schedule, and when the airplane levels at the missed approach altitude the After Takeoff checklist is called for.
A 737 certified for it may make a Flaps 5 go-around after a Flaps 30 approach. The FAA FSB report requires an AFM appendix, a supplementary procedure and operational approval for this, and training that covers the flightcrew callouts. It found no handling difference between the NG and the MAX, so training on either covers both. The FAA has also issued a Safety Alert for Operators, SAFO 10005, Go-Around Callout and Immediate Response (see go-around and missed approach).
Landing roll callouts
On touchdown the PF confirms the thrust levers closed and the SPEED BRAKE lever UP, lowers the nose wheel to the runway without delay and watches the autobrake work. The PM makes three calls:
- "SPEED BRAKES UP" once the lever is seen UP, or "SPEED BRAKES NOT UP".
- "REVERSERS NORMAL" when both REV indications are green; "NO REVERSER ENGINE NUMBER 1", "NO REVERSER ENGINE NUMBER 2" or "NO REVERSERS" if an indication is missing or stays amber.
- "60 KNOTS". The reverse levers should already be on their way back: their movement starts by 60 kt so that they are at the reverse idle detent before taxi speed.
Warning: in the FCOM's words, "after the reverse thrust levers are moved, only a full stop landing can be made"; an engine stuck in reverse rules out safe flight.
Before taxi speed the autobrake is disarmed and the PF continues on the pedal brakes. If the landing was automatic, the autopilot comes off and the airplane is steered by hand; airplanes with fail-operational autoland disengage it before turning off the runway.
Callouts for deviations
After 1,000 ft above field elevation the PM calls any significant deviation from the programmed airspeed, descent or instrument indications. The airplane helps: the amber ALT DISAGREE alert comes on when the two pilots' altitude indications disagree by over 200 ft for over 5 continuous seconds, and the IAN check at the final approach fix catches altimeters more than 100 ft apart.
Deviation callouts continue in non-normal flight. Through a nose high or nose low upset recovery the PM keeps calling out attitude, airspeed and altitude. In an approach to stall or stall recovery the PM monitors altitude, airspeed and the terrain trend and calls any omitted action. For task sharing, briefings and approach gates in general, see crew coordination, briefings and callouts and stabilized approach.
Frequently asked questions
What are the standard takeoff callouts on the Boeing 737?
At 80 knots the PM calls 80 KNOTS, and the PF confirms the airspeed and replies CHECK. The PM then confirms the automatic V1 aural, or calls V1 itself, and calls ROTATE at VR as the PF rotates toward a 15 degree pitch attitude. When the altimeter shows a climb the PM calls POSITIVE RATE; the PF replies GEAR UP, and the PM moves the gear lever up.
Who calls MINIMUMS on the Boeing 737 and what does the pilot flying answer?
The pilot monitoring calls APPROACHING MINIMUMS 100 ft above the decision height, decision altitude or MDA, and MINIMUMS on reaching the DH or DA, or the missed approach point. The pilot flying, who has been looking for the runway, answers LANDING if the required visual reference is established and GO AROUND if it is not. On most 737s the GPWS also gives automatic minimums callouts.
What callouts does the pilot monitoring make after touchdown on a 737?
First the PM looks at the SPEED BRAKE lever and calls SPEED BRAKES UP, or SPEED BRAKES NOT UP if it has not moved. Next come the reversers: REVERSERS NORMAL with both REV indications green, or, for a missing or amber indication, NO REVERSER ENGINE NUMBER 1, NUMBER 2 or NO REVERSERS. Last is 60 KNOTS, the point by which the reverse levers start back toward reverse idle.
What happens if the pilot monitoring misses a callout on the 737?
Boeing's philosophy is that the pilot monitoring calls from the instruments and the pilot flying verifies and acknowledges. If the pilot monitoring does not make a required callout, the pilot flying makes it. The FCOM also warns that a callout missing at the expected moment may mean a failed system or indication, or an incapacitated crewmember, so a silence is investigated rather than ignored.
Why are there two APPROACHING MINIMUMS calls on some 737s?
One is the crew callout, which the FCOM table places 100 ft above the DH, DA or MDA. The other is the automatic GPWS callout, which on most variants sounds 80 ft above the minimums set on the captain's MINS selector, using radio or barometric altitude as that selector is set. When the automatic callout sounds, the pilot flying acknowledges it; if it fails to sound, the pilot monitoring makes the call.
Test yourself on B737 Standard Callouts
The v1prep banks cover this topic in the B737 type-rating bank, with a worked explanation for every answer. EASA ATPL, PPL, IR and CPL, the FAA written tests and type ratings for the A320, A330, A350, 737, 767, 777, A220, 787, ATR 72 and E-Jet.
Start practicing →Sources and further reading
Library articles are written for study and exam preparation. They do not replace your aircraft's approved documentation, your operator's procedures or the regulations themselves.