Skip to content

The HSI and the RMI

NavigationPPL · IR · ATPL11 min readUpdated Nov 2026
Definition

The horizontal situation indicator (HSI) is a slaved heading indicator with a course deviation display built in, giving a plan view of the aircraft against a selected course. The radio magnetic indicator (RMI) combines a slaved compass card with needles that point at tuned VOR, NDB or GPS sources, so bearings to and from them are read directly.

The horizontal situation indicator (HSI) and the radio magnetic indicator (RMI) are the two classic instruments that put heading and radio navigation on a single dial. Each is built around a compass card that turns by itself, driven by a remote compass or an inertial reference, so the pilot never adds or subtracts heading. They answer different questions. The HSI places the aircraft against a course the pilot has chosen. The RMI points at the stations themselves, with nothing to select.

Neither belongs only to older panels. The HSI is the compass rose at the foot of light-aircraft glass displays such as the Garmin G1000, the rose modes of an airliner's navigation display redraw both, and many airliners keep an RMI as a standby. Problems built on them appear throughout EASA IR and ATPL radio navigation papers and the FAA instrument rating knowledge test. Navigation displays and indicators surveys the whole family; this article works through reading these two in detail.

From separate instruments to the HSI

A basic training panel spreads the same information across three instruments. A heading indicator shows heading from a gyro; a VOR indicator shows deviation from the course set on its omni bearing selector (OBS); an ADF indicator shows the relative bearing of an NDB. The pilot joins them up mentally, and a VOR indicator left with its OBS on the reciprocal of the direction of flight senses in reverse.

Cessna instrument panel: airspeed, attitude and altimeter dials in the top row, turn coordinator, heading indicator and vertical speed below, and two VOR indicators with OBS knobs on the right.
The panel of a Cessna 172P. The heading indicator (below the attitude indicator) and the two VOR and localizer indicators on the right, each with its own OBS knob, are separate instruments. An HSI merges a slaved version of the first with one of the others.Kentaro Iemoto from Tokyo, Japan · CC BY-SA 2.0 · Wikimedia Commons

The HSI merges the first two. The FAA's Pilot's Handbook of Aeronautical Knowledge (PHAK) describes it as a direction indicator whose compass card is driven by a flux valve, combined with VOR, localizer or GPS course guidance and a glideslope. The RMI merges the first and the third, and serves the VOR as well: a slaved compass card carrying two bearing pointers.

The heading indicator inside an HSI

The compass card of an HSI is a heading indicator in its own right. Heading is read under the lubber line at the top or, on a glass display, in the box above the card. What differs is the source. A free heading indicator, or directional gyro, has no sense of north: it keeps the heading the pilot set and then drifts. Bearing friction makes the gyro precess, and its axis also stays fixed in space while the earth turns at 15° an hour, which on its own can put the reading out by as much as 15° for each hour of operation. The PHAK therefore has the pilot check it about every 15 minutes and reset it to the magnetic compass in straight and level flight at a constant speed.

An HSI's card is slaved instead. A magnetic sensor mounted away from the cockpit, the flux valve or magnetometer, keeps correcting the gyro, so the PHAK notes that such instruments generally need no adjustment; most airliners take heading from the inertial reference system. An HDG flag in view means the compass card is not working properly. If slaving fails, free (DG) mode turns the HSI into a plain directional gyro, synchronized by hand against the standby compass at intervals. How heading indicators, flux valves and slaving work is covered in heading indicators and compass systems.

Reading the HSI

The parts of a typical electromechanical HSI, as the PHAK labels them, are listed below. Glass displays draw the same elements.

Element What it shows Set by
Compass card and lubber line Magnetic heading Slaved automatically
Heading select bug The selected heading, followed by the autopilot or flight director in heading mode Heading knob
Course select pointer The selected course; its tail shows the reciprocal Course knob
Course deviation bar Where the selected course lies relative to the aircraft VOR, localizer or GPS receiver
Symbolic aircraft The aircraft, fixed in the center Nothing
TO/FROM indicator Whether the selected course leads to or away from the station Receiver
Glideslope pointer Deviation from the ILS glideslope Receiver
NAV flag, HDG flag Unreliable navigation signal; compass card not working Automatic

Deviation is angular for a VOR or localizer and linear for GPS. Most HSIs carry two dots either side of center; fed by a VOR, each dot is typically worth 5°, so full scale is about 10°. With a localizer tuned the bar reaches full scale at roughly 2.5°, about four times the VOR sensitivity. A GPS source rescales the bar with the phase of flight: 5 NM full scale en route (2 NM on WAAS units), 1 NM in terminal mode within 30 NM of the departure or destination airport, and 0.3 NM, or angular scaling, in approach mode. Glass displays name the source and the GPS phase beside the card.

The heading bug needs care. In heading mode the autopilot follows it continuously, so turning the bug starts a turn at once, at the autopilot's normal bank limit.

Garmin G1000 primary flight display with a compass rose at the bottom: heading 147 in a box, HDG 135 and CRS 148 boxes beside it, a magenta course pointer and the label GPS TERM.
The HSI of a Garmin G1000 primary flight display: heading 147° in the box above the card, the heading bug set to 135°, and the magenta course pointer and deviation bar on a GPS course of 148°, the bar centered. TERM shows the GPS in terminal mode, where full-scale deflection is 1 NM.WKHarmon / Kyle Harmon · CC BY 2.0 · Wikimedia Commons

Course deviation and TO/FROM indications

The deviation bar sits on the course pointer and turns with the card, so the HSI is a map seen from above. The symbol in the middle is the aircraft and the bar is the course line, drawn parallel to the pointer at the displacement the receiver measures. A bar left of the symbol means the course lies to the left in that picture, whatever the heading, and turning toward the bar closes on it; a 30° intercept is the usual textbook figure.

The TO/FROM indicator is a triangle that depends on where the aircraft is, never on its heading. Pointing to the head of the course pointer, it says the selected course, intercepted and flown, leads to the station; pointing to the tail, that the course leads away. It flips as the aircraft crosses the line through the station perpendicular to the selected course, so the flip, not the first swing of the bar, marks station passage.

Because pointer and bar turn together, an HSI cannot reverse sense provided the correct course is set. The proviso matters on a localizer: the receiver measures only the displacement from the centerline, and the pointer decides on which side of the card it is drawn. With the published front course set, the bar reads correctly even on the back course. With the reciprocal set, the deflection is the right size but on the opposite side, and turning toward it makes matters worse. A conventional CDI has no such cure: its OBS has no effect on a localizer, so inbound on a back course the pilot must turn away from the needle.

Exam tip: to place an aircraft from an HSI, take three steps. The course pointer with the TO/FROM arrow gives the side of the station; the bar gives the side of the course line; the heading plays no part in the position.

An aircraft north-east of a VOR, on the 060 radial and heading 120°. An HSI with 060 selected shows FROM and a centered bar however the aircraft is pointed, and the magnetic bearing back to the station, the QDM, is 240°. v1prep schematic.
An aircraft north-east of a VOR, on the 060 radial and heading 120°. An HSI with 060 selected shows FROM and a centered bar however the aircraft is pointed, and the magnetic bearing back to the station, the QDM, is 240°. v1prep schematic.Illustration © v1prep

The RMI and its needles

An RMI has a compass card slaved to the aircraft's heading source, a heading index at the top, two bearing pointers and a function switch for each pointer. Each pointer can be driven by a VOR, an ADF or a GPS waypoint, as the pilot chooses. Nothing is set on the dial: a pointer simply aims at its source. The two needles have different shapes, often single and double, so that they can be told apart at a glance.

FAA illustration of a light airplane seen from above, with a magnetic compass and a fixed-card ADF dial whose yellow needle points toward the station.
What the RMI replaces: a fixed-card ADF beside a magnetic compass (FAA illustration). The ADF needle gives only the relative bearing, so the pilot adds the heading from the compass to find the bearing to the station. An RMI's card turns with the heading, so its needle shows that bearing directly.Federal Aviation Administration · Public domain · Wikimedia Commons

Everything an RMI shows can be read from one needle and the card:

Quantity Where it is read Arithmetic
QDM, magnetic bearing to the station Under the needle head Heading plus relative bearing
QDR, magnetic bearing from the station (for a VOR, the radial) Under the needle tail QDM plus or minus 180°
Relative bearing Clockwise from the heading index to the head QDM minus heading, plus 360° if negative
QUJ, true bearing to the station Not shown QDM with variation applied: east added, west subtracted
QTE, true bearing from the station Not shown QDR with variation applied the same way

Which variation applies depends on the source. A VOR radial is measured from magnetic north at the station, so a VOR QDR becomes a QTE with the station's variation. An ADF bearing on the RMI is built on the aircraft's own magnetic heading, so it is converted to true with the variation where the aircraft is. Over long distances a radio bearing follows a great circle, and plotting it on a Mercator chart also needs the conversion angle (see convergency and conversion angle).

On the ground, a VOR test facility (VOT) makes every receiver read the 360 radial, so the needle of an RMI fed by a serviceable VOR receiver settles on 180 whatever the OBS shows.

Flying with the RMI

Keeping the needle head on the nose in a crosswind is homing: the wind keeps pushing the aircraft off the straight line, so it curves round on the downwind side and covers more distance. Tracking holds a wind correction instead. The aircraft is on the desired inbound track when the needle head reads that track, whatever the heading; with the correction applied, the head sits off the nose on the downwind side.

Flying a DME arc, the RMI pointer is held close to the wingtip reference. If the distance grows, the aircraft is drifting outside the arc: turn toward the station, putting the pointer slightly ahead of the wingtip. If it shrinks, turn away (see flying a DME arc).

RMIs in airliners

Many airliners kept an RMI as a standby. The Boeing 737 NG's standby RMI shows magnetic heading with VOR and ADF bearings and runs from the AC standby bus, so it keeps working once all normal AC power has failed, for as long as the battery lasts. The A320's DDRMI takes its card from ADIRU 1, or ADIRU 3 when selected. VOR 1 or ADF 1 drives its dashed pointer and VOR 2 or ADF 2 its double one, and its DME counters show whole miles beyond 20 NM and tenths of a mile closer in.

The card matters as much as the needles. When the 737 NG loses heading, the ADF pointers leave the display units and the standby RMI's ADF pointers no longer give a correct magnetic bearing, though the relative bearing may still be right if the receiver works. The A320's DDRMI needs a valid heading signal before it shows VOR bearings.

Worked interpretation problems

Exam questions show an instrument and ask for a position, a bearing or a turn. The method never changes: separate what depends on position from what depends on heading. In the HSI problems each dot is 5°.

1. RMI, VOR. Heading 040°, VOR needle head on 100°. The QDM is 100°, so a right turn onto 100° flies to the station in nil wind. The tail reads 280°: the aircraft is on R-280, west of the station and a little north. The relative bearing is 100 − 040 = 060°, 60° right of the nose.

2. RMI, NDB, with variation. Heading 200°, ADF needle head on 330°, variation at the aircraft 6°W. The relative bearing is 330 − 200 = 130°, behind the right wing. The QDR is 150°. With westerly variation subtracted, the QUJ is 324°(T).

3. HSI, which side of the radial. Course 090°, TO, bar one dot right of the aircraft symbol, heading 070°. The TO arrow with 090° selected puts the aircraft west of the station, near R-270. With the card turned to 070°, a bar right of the symbol places the course line south of the aircraft, so the aircraft is about 5° north of R-270, on R-275. To intercept, turn right toward the bar, for example onto 120°, a 30° intercept.

4. HSI, heading irrelevant. Course 180°, FROM, bar centered, heading 250°. The aircraft is on R-180, due south of the station, crossing the radial toward the south-west. A centered bar shows where the aircraft is, not where it is going; to track outbound, turn left onto about 180°.

5. HSI, course set the other way. Course 045°, FROM, bar centered, heading 225°. The aircraft is on R-045, north-east of the station, flying toward it with the course pointer behind it. The picture is correct, but the usual setting inbound is 225°, which puts the pointer on the nose and turns the arrow to TO.

6. Localizer back course. Front course 270°, flying the back course inbound on 090°, front course set on the HSI. The bar lies left of the symbol: the centerline is to the north, so turn left toward it. A conventional CDI in the same place would show its needle to the right, and the pilot would still have to turn left, away from it.

7. Two RMI needles. Needle 1 on VOR A, head on 030°; needle 2 on NDB B, head on 120°. The aircraft is on R-210 of A and on QDR 300° from B: south-west of A, north-west of B, where the two position lines cross.

Frequently asked questions

Is an HSI the same as a heading indicator?

An HSI contains a heading indicator: its compass card shows heading under the lubber line. The difference is that the card is slaved to a flux valve or an inertial reference, so it does not drift like a free directional gyro, which the pilot realigns with the magnetic compass roughly every quarter of an hour. Around the card the HSI adds a course pointer, a deviation bar, a TO/FROM arrow and a heading bug, turning it into a navigation instrument.

How do you tell which side of the course you are on with an HSI?

Read it as a map seen from above. The aircraft symbol is the aircraft and the deviation bar is the course line. If the bar is left of the symbol, the course lies to the left in that picture, so turn left toward it. The heading does not change the answer, because the course pointer and bar turn with the card. The TO/FROM arrow then shows on which side of the station the aircraft is.

What does the tail of an RMI needle show?

The tail gives the QDR: where the aircraft lies from the station, as a magnetic bearing. With a VOR selected this is simply the aircraft's radial, so a needle head on 110 means the 290 radial. The head gives the QDM, the magnetic bearing to the station and the heading to steer to it in nil wind. Both are read straight off the card because it is slaved to the heading source.

How do you find the relative bearing on an RMI?

Relative bearing is the angle from the nose, measured clockwise, to the station. On an RMI it is the angle between the heading index and the needle head, or QDM minus heading, adding 360 if the answer is negative. With heading 300 and the needle head on 255, the relative bearing is 315: the station is 45 degrees left of the nose.

How do you fly a localizer back course with an HSI?

Put the published front course on the course pointer, also when the approach uses the back course inbound. The localizer receiver only measures displacement from the centerline, and the course pointer orients that displacement on the card, so with the front course set the bar senses correctly and the pilot steers toward it. With the reciprocal set, the deflection is the right size but drawn on the opposite side.

Test yourself on The HSI and the RMI

The v1prep banks cover this topic in General and Radio Navigation (061/062), with a worked explanation for every answer. EASA ATPL, PPL, IR and CPL, the FAA written tests and type ratings for the A320, A330, A350, 737, 767, 777, A220, 787, ATR 72 and E-Jet.

Start practicing →
15,000+ questions · EASA & FAA · Free to start

Library articles are written for study and exam preparation. They do not replace your aircraft's approved documentation, your operator's procedures or the regulations themselves.